Multi-Rotor, Build it by yourself
CleanFlight failsafe in operation. Test CleanFlight 1.12.0 Failsafe-RTH and Failsafe-Land. Mar 24, 2016 Test failsave stage#1 (Channel Fallback Setting) and stage#2 (Failsafe Landing) of firmware CleanFlight (F3 32bit) version 1.12.0, channel fallback setting to do failsafe-RTH Dead Cat Pro /
Read more
RadioLink AT9 2.4G 9CH with receiver R9D that have SBUS port. RadioLink AT9 9CH and R9D 9CH receiver. when use SBUS port. it can operate as 10CH radio. all 10 channels are in SBUS one wire already, and R9D will
Read more
I want to stabilize MOBIUS camera for smooth aerial video, So I start to build gimbal for it. At this time, 2D brushless gimbal is cheap but also have good performance. and these are my choose for build my 2D
Read more
I want to build my camera for my used of inflight video record and FPV+OSD. I think that “Raspberry Pi2 mini computer” and it camera module can used for my need. then i start to do it … The RasPi
Read more
April 24, 2015 i was modified board KK 2.1 for run with firmware MultiWii 2.4 after modified this KK 2.1 can support GPS, telemetry, waypoint navigation and all feature of MultiWii 2.4 Board KK 2.1 have MPU Atmega644PA run at
Read more
April 12, 2015 Flight for test MultiWii 2.4 FENCE-RTH. MultiWii 2.4 have FENCE-RTH feature, that can define fence radius in meters. when fly over fence range, it will auto activate Return-To-Home (RTH). FCB/FW: My build MEGA2560 / MultiWii 2.4 OSD/FW:
Read more
April 4, 2015 my test flight for MultiWii 2.4 auto pilot MISSION flying through defined waypoint and auto landing at last waypoint. Auto pilot flying from waypoint #1 to waypoint #7 then auto landing. YouTube => https://www.youtube.com/watch?v=zBYKLIiuwtQ
Read more
April 1, 2015 AOMWAY 5.8GHz 32ch. Video & Audio receiver with build in video recorder. Now i can record my FPV+OSD screen while flying by this receiver. My multi-rotor have more safety with OSD data that have GPS location on
Read more
April 2, 2015 I got it yesterday, the big size X900 tri-copter kit, then today i open it box. let all see what’s inside a box. my assembly 🙂 Tail-Tilt servo install (servo not include in kit) Install electric set
Read more
Mar 31, 2015 I build one arduino as ISP (in circuit serial programming) that can program other arduino, both firmware and boot-loader. Normally arduino board can upload firmware by use software arduino via FTDI USB. but when boot-loader of arduino
Read more
Mar 29, 2015 I was upgraded my tail-tilt-rotor of my build tri-copter to use double servo-rod instead of single servo-rod, and change motor/prop to bigger size N2830 /prop 1147. All can see my build tail-tilt-Rotor working in this video Smith
Read more
Good news, MultiWii just release new version 2.4 on March 15, 2015 MultiWii 2.4 have waypoint navigation feature, and have nice function return to Home and auto landing. and also FENCE is very nice for protect fly away, if it
Read more
Mar 14, 2015 My build FPV screen sun hood. it perfect for me. I can see video on FPV screen very bright & clear, without disturb by sunlight or light reflex. Mar 17, 2015 Smith Tri-Copter FPV OSD : HUD
Read more
Mar 8, 2015 Smith Tri-Copter FPV : FLIP MISSION i want to know that my build Tri-Copter can fly FLIP or not ? after fly acrobatic, i know that my tri-arm are too flexible. it can’t support high G force.
Read more
My build Tri-Copter that start build on March 1, 2015 Mar 1, 2015 This’s the first flight video 🙂 my build Tri-Copter just finished build, then doing the first test for check all flight system. MultiWii SE V2.5 / MultiWii
Read more
build COBRA AH-1 head shell that made by foam and sticker paper. Feb 17, 2015 MultiWii 2.4 bi-copter AH-1 Cobra head shell i build AH-1 COBRA head shell for my bi-copter. This video is short demo Feb 18, 2015 MultiWii
Read more
Feb 1, 2015 Smith Bi-Copter V1.2 I change flight control board to KK2.1 use firmware 1.19S1 Pro and add bottom plate for lower CG Feb 1, 2015 KK2.1 dualcopter FW 1.19S First test my build bi-copter installed with KK2.1 FW
Read more
My build Bi-Copter that start build on Jan 1, 2015 Jan 13, 2015 Smith Bi-Copter : Fly for test PID My build Bi-Copter, today i found PID that can fly. but i must continue do tuning it PID for better
Read more
These are all things about FPV and OSD devices that i used 🙂 Nov 9, 2014 DIY quad copter FPV+OSD Flight test Test flight with my DIY quad copter that have FPV (First Person View) and OSD (On Screen Display)
Read more
Nov 9, 2014 DIY quad copter FPV+OSD Flight test Test flight with my DIY quad copter that have FPV (First Person View) and OSD (On Screen Display) devices. Oct 27, 2014 DIY quad copter S500 test FULL AUTO flight test
Read more
Oct 18, 2014 My Quad X – Full auto flight test full automatic flight, since take off until landing. FC : Smith DIY Flight Con. Atmega2560 / FW : ArduPilot NG 3.1.5 / App : DroidPlanner / SW: APM Mission
Read more
Sep 13, 2014 My Quad X – FIRST FLIP I setup MultiWii 2.3 to HORIZON mode. this mode let FLIP possible. This flight is the first of my x-copter and me to fly in ACROBATIC action and try FLIP !!!
Read more
June 27,2014 My Quad X V2 – GPS P-Hold while climb up & down at evening. i do testing about function GPS position hold, while altitude climp up & down by control only throttle stick. June 28, 2014 My Quad
Read more
June 13, 2014 My QUAD V2 – MultiWii SE V2.5 use external compass I found a big problem, a compass sensor on board “MultiWii SE V2.5” was interference by power wire. while throttle-up, compass sensor measure wrong about 30 degree.
Read more
This’s my second build for quad-X, start build on May 30, 2014 June 5, 2014 My Quad X Ver.2 – Flight #2 good flight stabilization after FC profile tuned and do water level while gyro & acc calibration, it have
Read more
My first build quad-copter, I start to buy devices on May 6, 2014 🙂 frame: FPV 450 motor/prop: 2212 1000KV / 1045 composite ESC: Dragon 30A Battery: Li-Po 11.1V 3000maH 30C Radio/receiver: STORM i6S 6CH / STORM S603 DSMX May
Read more